Getting started with Managed Power (US & Canada)

Topic

This article provides physical installation and initial setup instructions for the US & Canada based Managed Power devices.

Environment

DMP-PDU-6R-515
DMP-PDU-14R-515

Description

The Managed Power devices can be configured and managed through the Datto Network Manager user interface. The models are primarily distinguished by the number of ports on each.

The DMP-PDU-6R-515 provides six fully-managed and monitored power ports.
The DMP-PDU-14R-515 provides fourteen fully-managed and monitored power ports.

For more information on the features of each device, see: Managed Power: Features & Specifications (US & Canada).

Physical Installation

This power strip is designed to be set on the floor or desktop, or mounted to a wall.

Physical Installation:

These devices are intended to be used in a location having equipotential bonding (such as a telecommunications center, a dedicated computer room).
Installation requires verification of a Protective Earth Grounding connection of the socket-outlet by a Skilled Person.
Do not use extension cords or adapters with this PDU.
Never install PDU or associated wiring equipment during a lightning storm.
Ensure that all power cords, plugs, and sockets are in good condition.
Avoid moving the device while in use.
Do not install near potential sources of water or fire.
Do not place heavy objects directly on the PDU.
The mains plug/appliance coupler is used as the disconnect device.
The device should not be located at a place where it is difficult to disconnect the mains plug/appliance coupler.
As a Safety measure, any port measuring higher than 15A will disable itself. Ports can be re-enabled by logging into Network Manager.

IMPORTANT Risk of Explosion of battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

Whats Included

Below is a list of what is included in the box with the device:

	DMP-PDU-6R-515	DMP-PDU-14R-515
Included Accessories	(1) NEMA 5-15P to IEC C13 Power Cable (2) Short Rack/Wall Brackets (2) Deep Rack Brackets (8) Bracket Screws (4) Wall Mounting Screws (4) Drywall Anchors Mounting (4) Rubber Feet	(1) NEMA 5-15P to IEC C13 Power Cord (2) Short Rack/Wall Brackets (2) Deep Rack Brackets (8) Bracket Screws (4) Wall Mounting Screws (4) Drywall Anchors Mounting (4) Rubber Feet (1) Retention Clip

Rack Mounting

The device can be mounted to a rack in either orientation using either set of adapters provided.

Front Rack Mounting -Short Adapter

Front Rack Mounting -Long Adapter

Rear Rack Mounting -Short Adapter

Rear Rack Mounting -Long Adapter

Wall-Mounting

The Managed Power device can be wall mounted either vertically or horizontally using the short rack brackets and the included wall mounting screws and/or drywall anchors.

Setup & Registration

Connect the supplied power cable from a grounded 120V outlet to the input C14 socket.
Connect an ethernet cable with Internet access into ethernet port 1 or 2.
Sign into the Datto Partner Portal (portal.dattobackup.com).
From the header menu, select Status > Networking Status.
Select the name of a Network or Launch Network Manager, to load the Networking Manager.
In the networking portal, ensure you configured the correct time zone for the network.
Navigate to Power > Add New and enter the MAC address. Use the drop-down arrow to enter multiple MAC addresses at once, or upload a CSV file containing the MAC addresses you would like to use.

FAQ

Do the Managed Power devices offer surge protection?

Yes. Read our article on Surge Protection for more information, and what do to if surge protection depletes.

How do the Managed Power devices access the internet?

The device can access the internet via Ethernet.

Connect it to any router or switch that provides a DHCP connection, and the device will check in to the cloud.

Can the the Managed Power device act as an access point?

No. While it uses Datto's mesh technology to go online, it cannot act as an access point.

What causes the ports or the strip to trip?

An individual port will trip and shut down if it draws more than 15A for a few seconds. On a 120V circuit, this is approximately 1200W per port. If a trip occurs, the cloud management portal will show the port as disabled. You can re-enable a disabled port through the cloud management UI. The entire strip has a breaker rated for 16A, that at varying temperatures and loads will change the trip time. A direct short will trip the whole circuit breaker, disabling all ports. That mechanical trip will require the button to be pressed on the device.

How does the the Managed Power device prevent shorts and overloads to the unit?

The device has an electro-mechanical circuit breaker to prevent shorts and overloads to the entire unit. The total combined maximum current allowed is 16A. The unit will trip in a varying amount of time, depending on the percentage of current overloaded and temperature.

At 16A, it will not trip unless it crosses the 65 C temperature threshold.
At 20A, it will trip within an hour or if it crosses the 60 C threshold.
At 24A, it will trip within 5 to 30 seconds or sooner if it crosses the 60 C threshold.
At 32A or above, it will trip within 1 to 5 seconds or sooner if it crosses the 60 C threshold.

As a safety precaution, if the entire circuit trips, the connected equipment will all be disabled. The USB ports and the Access Point hardware will continue to operate. In this state, the unit will no longer be cloud manageable for the ports as they are all disabled via the breaker. The device may need to be physically reset by using the Reset button on the device, located next to the power cable receptacle.

What is the difference between a circuit breaker (trip) and a surge protector (surge)?

Circuit breakers interrupt power when the electrical current exceeds a certain threshold, whereas surge protection provides voltage overload protection. Circuit breakers prevent too much current from being pulled or short-circuiting from occurring, while surge protection prevents large voltage spikes from entering the devices.

Additional Resources

Getting started with Managed Power (International)
Managed Power: Features & Specifications (US & Canada)
Managed Power FCC & IC Compliance

	Need troubleshooting help? Open the Kaseya Helpdesk.
	Want to talk about it? Head on over to the Community!
	Have an idea for a new feature? Want to learn about upcoming enhancements? Visit the Ideas forum!
	Provide feedback for the Documentation team.