AP840E quick start guide

Topic

This article describes how to get started with the Datto Networking AP840E Access Point

Environment

  • Datto AP840E Access Point

Description

The Datto AP840E Access Point is designed for installation either indoors or outdoors with several mounting position options.

IMPORTANT  This device does not support passive Power over Ethernet. Attempting to power it in this manner can result in hardware damage and may void your warranty.

Index

What's in the box

Your AP840E package should contain the following:

  • 1 Datto AP840E Access Point

  • 4 high-gain omidirectional antennas

  • 4 M4-25 drywall screws

  • 4 wall anchors

  • 1 M4-8 grounding screw

  • 2 Ethernet cable grommets

  • 1 mounting plate

  • 4 M6-10 mounting plate screws

  • 1 port cover and gasket

  • 10 M3-10 port cover screws

  • 1 M3-8 torque security screw

  • 1 Allen and torque combo tool

  • 1 blank LED indicator tab

Physical installation

This access point is designed to be installed either indoors or outdoors with several mounting position options. When mounting this access point, keep the following in mind:

  • 802.3at PoE input

  • Place the access point at the center of the room, away from metallic surfaces.

  • Do not place heavy objects on the access point.

  • Install the access point in an area free from strong electromagnetic sources.

  • Check the Ethernet cables to ensure they are fully secured to both the access point and the PoE injector or switch.

  • Do not install the access point in plenum spaces. Use the ceiling mount instead.

Electrical hazard: Only qualified instructed or skilled personnel perform installation, repair, or disassembly procedures.Risques d’életrocution: Seul un personnel qualifé ou qualifié doit effectuer les procédures d’insallation, de réparation ou de démontage.

Installation considerations

  • The 2.5G ethernet port is PoE input only. Ports do not include PoE passthrough and are not able to supply PoE to other devices.

  • The AP840E WiFi-6 Access Point cannot be powered by passive PoE.

  • Passive 24V PoE is not supported on this device. Do not plug 24V PoE into the access point. Damage can result.

  • Le PoE passif 24V n’est pas pris en charge sur cet appareil. Ne branchez pas sur le systéme. Des dommages peuvent en résulter.

Surface mounting

You can mount the APAP840E on a wall or ceiling.

1. Install the flat side of the mounting plate on a wall or solid ceiling with the included drywall screws and anchors. Make sure the arrow on the mounting plate is pointing up.

2. Install the mounting plate screws into the access point.

3. Attach the antennas by rotating them clockwise onto the four threaded antenna posts. This access point supports 2.4 GHz and 5 GHz antennas.

4. Connect an Ethernet cable to the 2.5G Ethernet port, with a 802.3at PoE source. Wrap the grommet around

the Ethernet cable, then insert it into the port plug and install the port cover with the provided screws.

5. Align the mounting plate screws on the AP with the mount holes. Slide the AP down onto the mounting plate, then secure the access point with a security screw. Finally, attach a grounding cable (not Included).

Pole mounting

When pole mounting use maximum 1/2 inch-wide metal clamp cables (not included). Do not use plastic zip ties.

1. Install clamp cables through the slots on the mounting plate.

2. Repeat steps 2 through 5 from the surface mounting instructions above.

Cloud management

To connect your access point to Datto Network Manager, follow the instructions in the How to set up cloud management on Datto AP840 and Datto AP840E Access Points article.

Additional Resources